Solutions for house...

Solutions for hotels...

Solutions for company...

How to Install

 

 

Please read bellow practical installation descriptions and recommendations for EOC, GEPON and Powerline Networking technoligies!!


 

Adapters Wodaplug EOC – Ethernet over koaxial networks 

Practical experiences and how to use Wodaplug EOC Master and Slave devices in coaxial networks TV or SAT – solution for problem situations

  1. Coax cable link Attenuation 

When you use the EOC Wodaplug Master and Slave units, it is necessary to have  coaxial lines in good conditions. For TV signal transmitted in band above the 85MHz may be all well and good, but it doesn’t have to be same for range 2-65MHz .

On the route to the Slave there is always some attenuation on the main coaxial cable, but also passive elements such as hubs, splitters, connectors. The hubs is nessesary to calculate with the weakening in 3.5-4dB for 2-way splitter, 3-directional attenuation has a 5.5-series 6 d, 4 directional around 8dB, 6-directional approx. 12dB. turners have an intermediate direction of attenuation, attenuation is by the type of splitter around 1dB.

I tis nessesary to realize, that this kind of attenuation is between input and output. Lets pretend –  If we would connect master unit likewise oposite direction, direction to input there will bet he same attenuation , but towards another output this very same attenuation will be much higher, during the manufacturer datas, it will be around 25-30 dB. It means, that if we would like to inject master unit somewhere located in middle of network architecture and not on its begining (ofcoarse not over build in diplex module, but over whole splitter) , there will be in one direction attenuation for example  thru double splitter apr 4dB, but for passing part of the network it will get as much as around 30 dB.

Becoase of that, if we want to use master unit to higher distance, where every degree of attenuation counts, is very very important to find perfect spot for master unit placement injectment, ussually best possible is near or next to group station, optical reciever (see our other optical products or our already connected willage sample), or simply source of the signal.

The difference in temperature, also causes differend attenuation shown by master unit in the summer and another in the winter. For this you need to remember, especially if it is some sort of Slave to the edge of the  parameters  in the winter, it can be assumed the problem with arise in warmer weather, therefore,to avoid this as much as possible, enhance the route parameters.

The values indicated in the management of wodaplug master through a Web interface are very helpful, although they are not completely accurate, they help create a picture of the quality of the network and its individual segments.

  1. Connectors – rust is blast

A very important part of the koaxial network are connectors, or the execution of their Assembly. By The influence of time and meteorological conditions, however, the metal parts of the oxidation layer is generated, which increases the resistance of the structure. What has a very negative impact on the transmission, mainly in TV zone, in which bandwith these devices works as well. From ours many years of experiences, we can state that the situation can be drasticly improved by cleaning every connection, IE. screw out connectors, spray over with a suitable spray eg. Contact 60 and screw back the connector. The parameters of the connection between wodaplug Slave will improve. doing so on whole route between wodaplug master and slaves, it will make a significant improvement in SNR, which ultimately will increase parameters of the network throughput. When outdoor hubs/splitter are well maintained too, it will also help. Always keep in mind !!! Rust is blast for your network.

 

 We had a lot of cases where the wodaplug Master unit showed attenuation around 60dB, and even sometimes wodaplug slave unit was not available, After treatment of the route  the parameters of the connection improved so greatly, that downturn was suddenly only 50dB and the Slave unit goes steadily ever after. (it really happend many times in our instalations and not only at kingdoms far far away :) )

Sometimes when experiencing bad parameters of the network – may help to reduce the output power of master unit, whether using lovering cells or  through the Web interface. Sometimes in network  may be a weaker place, for example poorly made grounding, network cable (dismantled or badly fitted drawer). This place then causes a strong signal reflections, and then distort the signal and so worsen the parameters across the whole network, which has an impact on the availability and the slave units to communicate.

 

  1. Galvanic separators

Another of the problems that may emerge, is the formation of various  currents flowing thanks to connecting multiple   several different groundings, for example. from the various phases of a variety of grounding terminals, grounding … Each grounding unit has a different potential and when they come across such a pack of two, there is rising of the potential for tension between them and current begins to flow between them. It is, however, interference for TV signals within 65MHz  and reduce it again the total capacity of the transmission, or it may cause disconnection of slave units from the MASTER unit.

Also the source of such interference can be made by a source of tension, for sample bad adapter, the TV networks are often involved in computers networks today,for example: TV with 3way plug, in this way, there is unwanted conection between grounding from TV network and it colides with grounding from EOC network and we have problem alive. Such interference can often be seen in the main TV picture of the analog signals such as moving vertical strips.

The solution may be galvanic separator, that separates these different groundings or resources. The best prevention is to involve  galvanic separator at the start of the tv antenna network (at the entrance to housings), this way you split/separate networks from each housing/area etc., if that doesn’t work, then you have to find the line bringing interference to TV networks and install (after punishing owner of the housing :) ) galvanic separator for this connection. proven by years of experience you may find this type of Polytronu model KTG220F very usefull. if you need to buy this or any work proven type, let us know.

 

  1. Diplex filters

Whereas these data signals spread in TV networks in the 0-65MHz back and forth directions, is necessary to ensure this way goes mainly through the amplifiers. Some of them (especially older nets) have only the active a reverse way , However, it is possible to bypass those amlifiers with pair of diplex amplifiers filters. The input signal to the amplifier plugs into the filter input 0-860MHz diplex, output of diplex 85-860MHz will be connect to input of amlifier, on the other side of this amlifier you connect signal again to diplex 85-860MHz and output from diplex 0-860MHz continue to tv network. In addition, these two diplexes are connected thru inputs 0-65MHz, which in real does so called bypass of the wired signals twoways around that amplifier

The second option is to Replace  amplifier with new with passive back direction 0-65MHz, what may also be a partial improvement of the signal due to the involvement of other connectors and jumpers in bypass.

 

  1. Coax networks with Multiswitch

Another option for connecting wodaplug is thru multiswitch – you need to connect Wodaplug eoc master to original terrestrial multiswitch  antenna input and multiswitch has to be in passive mode (make sure device is set in passive mode, ussualy its possible only when amplifier is off !!!) – thats what we dont want so often so we come to other possibility:

. Amplifying terrestrial signal with wodaplug in network thanks to its build is still possible, but used amplifier  has to be connected between Terr. antenna  and wodaplug EOC master device to not block data signal injected by Wodaplug EOC master in to Multiswitch. As every plus has its downside, we strongly recommend to lower output power on EOC master unit, in web interface on RF parameters section or using the cell. Try to find best solution to avoid  interferences. By our experiences is to lower signal to 112 – 110 dB for medium or bigger networks and 90-92 in smaller networks. At the place of wodaplug slave installation (end customer place – network user) , use ordinary diplex filter, avoid using wodaplug slave as direct coming thru signal in this scenario. You must separate bandwitch with diplex unit up to 67 MHz for slave unit. Please , bear in mind to use some good quality products.

 

multiswitch example

input signal using diplex filter

 

there is even third, ussually best option:

Wodaplug lab offers to ISPs option to bridge your old multiswitch units to make it EOC friendly by inside installing data/bandwith bypassers, we need to know what type it is and other helpfull info before we start . The price starts around 99 Euro per unit  and may vary from case to case.

 

  1. Practical experience

In practice, there been implemented a number of contracts with these devices on different types of networks and cables. Maximum achieved a distance of up to around 1800m, with the assistance of the use of the transponder/repeater in around the middle of this route, while the main route was on the cable type 860 (these are the ones used on major routes cables -most fat ones :)- ). When you plug in the transponder/repeater means slave and Master, it is necessary to separate the zone 0-65MHz for for those two units, whether by the filter, as well as it is best to engage the input and output of the amplifier, which has turned off reverse way 0-65MHz.

Whereas, however, the larger the trail, the more connections and devices connected to the network, and thus even more sources of interferences by the various reasons described above. Therefore, it is advantageous, as it can be, to make a passage through the optical network (please referr to our optical networks part) and up to its end of the optical node and put the Master connected to the media convertor(please referr to our optical networks part). there are many of networks made this way, and  the descibed problems disappeared,with no record of another problems. we split the network to half by this fibre-optic network and thus we achieved a significant reduction in interference in a separate network. wodaplug optic network are very reliable with best possible price.

As regards the number of wodaplug slaves on one wodaplug master unit, We have a networks, where it’s around 30 slave units, some customers have around 60-100. There should be no problem to involve even more of them, including around 120 as indicated by the manufacturer. Much more important is to do so called speed shaping  through an external router/server, best suited by brands us  Mikrotik , etc. These routers allow you to specify where the speed for each user sets with higher logic with respect to input connectivity. Although the master allows you to set the speed for each of the ports the slave units, however, redistribution is not used as a parameter value of input connectivity and, therefore, the greater the use of capacity to the network may seems sometimes in bigger networks cause stocking the network. The involvement of external router/server, which is managing , the problem disappeared. Of course, if  100% connectivity is used, the only solution is to increase the input connectivity.

A very important parameter, as I have already mentioned, it is, Its SNR It is, therefore, the signal-noise separation which determines the quality of the network for a given point of the network.

onlineslavesexample

 

This is a list of wodaplug slaves of the one master, where the connection between the SRN and the attenuation can be seen, in this network we have sometimes blackout only with the slave with the attenuation 60dB and SNR 5,44 and 4.72, but we talking the line in the House, where it goes through the hubs, couplings, connectors, link x it would be quite ok, if better conection can be possible. On the other hand, the slave, the fourth farest from the end has same attenuation 60dB, but the SRN 13,86, and also 22,22, whereas it is involved through less splitters, hubs, connectors, and so it also has a much better parameters speed. It is the most reliable attenuation around up to 50dB, but it works very reliably even at higher attenuation.

Real speed on this network was 100 MB/s, which is in many cases exactly the connectivity, but we have information from one of our customer that it had tested well at much higher speeds in real. It’s mostly about the technical parameters of the network, the device can really achieve the speed specified by the manufacturer is used chipset. Then when we reach over 300 MB/s speed tests.

 

The reference projects – Ethernet computer network over existing coaxial cable distribution (SAT/TV)

Appartment – Internet and HD IPTV for residents– Wodaplug EOC Master + Slave

Multi-floor apartment house, guest house or hotel with an existing coaxial network needs simply and without additional cables distribute the internet and IPTV to individual apartments – rooms. Thanks to the several floors and the area which makes it dificult to cover it by WiFi signal, to install the HW and also the amount of WiFi accesspoints would significantly burden on the electricity bill. Putting the new cables is not always possible. Therefore, let’s use the coaxial network which is nearly always present either as a common TV antenna (tree) or as a satelite network incoming signal with a hub (star).

Example of use in practice :

Wodaplug EOC Reference – deployment in apartment buildings connected by the optic cable on the internet network and the IPTV for individual entrances through the existing coaxial wiring:

In apartments there are an existing coaxial network systems, whether satellite antennas with combiners or splitters or the common television antennas. Tv technician simply adjusts the active parts in the network for every entrance of the house so it is bi-directionally data-through for band 6-65MHz and after that we connect Wodaplug EOC master to the input combiners / the splitters and then install end units Wodaplug EOC Slave to the individual flats. For each entrance of a residential house is typically one Master to one common coaxial network. The Master unit has the IP address management to setting up  the service / VLAN and QOS for individual clients. EOC line acts as a transparent smart Layer2 switch.

Therefore, in the apartment building, which is connected by the fibre optic, We connected master unit via Gbit dac. Further, there has been connected a total of 5 client units in the apartments of the final customers. Into the apartment on the specified VLAN runs IPTV in the form of a multicast. It is tested that the master unit can handle the 4 clients to deliver data for 4 different HD programs in a multicast. The fifth channel on the fifth unit was only SD, therefore a total flow was about 200Mb/s. Every HD program that we ran was moving data around 40-50Mbit/s. at least this flow flowed on one Vlan. At the same time with this multicast TV service still ran internet speed 100Mbit down. For each customer reserved 20Mb on the internet. Therefore, a total of approximately -300Mbit of service. At this load, everything worked and the picture on any channel has’nt made any mistake. But if we’re already turned on a HD program on the fifth slave unit (the other 5-th HD program), It has variously started to err IPTV picture and at different times on a different slave units it began pixeling or scramble. We reached the limit capacity of the EOC line between 300-350Mb/s. Therefore, for using IPTV with HD channels it is applicable for 4 to max 5 Slave units 100Mbit flow reserved for internet. Then the band for the transfer of data is already almost fully taken, it is possible to reduce the reserved part for the internet if you need in one network/the entrance of the house more than 4 customers with the service HD IPTV.

So thats in a nutshell everything about the practical test and deployment with HD IPTV. If it‘s just on the internet, then it’s cool and works even with 20 users and we don’t even know about it.

Connection to the network with splitter and Amplifier – For example 2 apartment houses connected by coax.

This is a practical realized example of Wodaplug EOC technologie connection into the existing SAT/TV splitter of 2 neighbor apartment – ilustration of the situation:

nakres

Detail of the previous existing splitter – in house n. 1 is merger with amplifier and with a splitter, in house n. 2 is amplifier and splitter. Then where should we place a data entrance and how we can solve a amplifier pass thru?

dum1Dum2

Solution : In a point A in house n.1 connect thru a diplex filtr Wodaplug EOC Master TV and DATA come into the splitter in the house 1 and at the same time into the house 2. At the entrance of the house 2 (in place of the red arrow) insert a diplex filter – input will merge the DATA with  TV. Output of the TV plug into the existing amplifier. To the point D connect other diplex filter– TV input into the amplifier output. The merged output of TV and DATA plug into the splitter. All we have left are the two outputs of a DATA on these diplex filters – connect them with the cable and now it start working – so data will go outside of the amplifier – tzv bypas.

reseni2reseni1

 

result : TV and data running in both houses! Photo of complete functional connection 

 

Optical GEPON village project

GEPON optical network project for the communities

Optical network for fast internet and smart HD TV in your community with a total cost below the $ 4000 ? It’s coming!

Services: Internet-222Mbps symmetrically and clever internet HD TV with recording and reflux by watching

 

Typical of the agglomeration with the new housing is the ideal solution for choosing G EPON technology. The density and the number of connected end-customers choose this cheaper uploaded wodaplug technology (due to the capabilities of the services provided and obtained speeds) with a shared optical cable.The great advantage is also a simple implementation and configuration of the Ethernet standard. And input costs? “Overall, including a 1 GB connection and distribution nepřesáhli when using wodaplug optical technology lines 100 USD”, says co-owner of the company that provides complete services in the field of data transmission and Patrik Prešl RETE applications.

 

 And how to do it, then?

 

As an input for the municipality article was established in-band microwave link 80 GHz 1 Gb full duplex, for whose location was voted the highest building in the village school. Network and service management with the old router preconfigured ISP services (HD TV, internet, etc. According to local requirements) and then followed by the EPON OLT Wodaplug WDS1U4PGE control unit, which has a dimension of 1U rack placement. 4 Gigabit EPON ports wodaplug WDS5441H-C (H) 3AL with range up to 20 km (in real terms) are more than adequate to cover all potential customers, in case of increase can be used 8-i port license unit. On each port can connect up to 64 end the units, but in order to ensure sufficient speed for the final user to connect up to 32 is optimal the units on a single port.

For the OLT unit therefore follows the optical tub with PLC splitery that divide a shared optical fiber into each of the branches toward the end customers. As appropriate, we chose the first 4:1 PLC spliterem , and then the next PLC spliterem 8:1 (that is, 4 * 8 = 32 end ONU for end-customers). The school, therefore, are based on 4 optical lines which are then further divided towards the houses of customers.

For the distribution network after the village we chose a combination of outdoor optical cable (16 threads in one) with the use of curtains on public lighting (non-standard, but cheap and perfect solutions for wiring in the already finished zones without having to interfere with the structures of communities) and in the new buildings then save the optical cable to the sidewalks. Optical fiber that we used for outdoor divorce, has 16 fibers in a single cable, there is also provision for a further increase in the number of trailing units. After adding an additional SFP module into the port PON OLT unit , simply use the same cable and its not yet unused thread come to life and will bring the signal to other stores. It will therefore be possible realistically without further significant cost to connect a total of 4 * 32 = 128 users (4 PON ports and 32 ONU on each)

 

Similar to how we have chosen and for the realization of all-optical networks in the other, a larger satellite town, where we already had customers connected over Wi-Fi. The transition from Wi-Fi to the optical network with elements of wodaplug was due to previous experience very simple, unpretentious, the costs outweighed the disappearance having paid reliably (e.g. outreach), and customers appreciate noticeable improvement services and stability. For a denser buildings, we chose the distribution of splitery in the 8:1 ratio running two in succession, the signal to us that once again came out optimally.

 

In General

 

Optical network behaves transparently as a smart switch, you can configure the VLANs are for individual ports end the. The configuration is simple thanks to the front of the programmed cutter path diameter of templates such as. previous installations. clone installation (when the 4 and 8 port OLT unit wodaplug offers template management!), so the newly connected the downloaded configuration according to the preset templates (provisioning ). Configuration of the OLT unit via the included configuration software EMS – central management (based on SNMP and mySQL and other needs to install SW on PC), or by using telnet and the CLI (command line interface). They also support protocol SNMP (mibs).

 

The competitive advantages of hardware

 

EPON OLT unit WDS1U4PGE are fitted with branded chipset Cortina CS8032, their performance and signal level is thus at a very high level and ensure wide coverage for your network stable signal and a varied range of deployable technology already proven services in practical deployments. For example, heat resistance was also tested in real conditions at temperatures much over 40 c.

The great advantage is also DUAL POWER supply, that is, the units have two redundant sources!

DIAGRAM of standard network configuation for an ISP with IPTV service (VLAN segmentation)Diagram-standart-zapojeni

Atention – not use VLAN 1 and 3, VLAN 3 is used for internal communication of Cortina chipset and is prohibited! VLAN1 use for management only!

Example of CLI configuration of an OLT unit Wodaplug for this scenario using templates – provisioning

1.       Config the OLT uplink port vlan:

epon# swport ge1                                                                                                                   

epon(GE-1)# vlan                                                                                                                                                                                        

epon(GE-1)# vlan add 7 tag                                                                                                          

epon(GE-1)# vlan  add 33 tag

2.       Config the OLT pon port vlan:

epon# swport ge5                                                                                                                   

epon(GE-5)# vlan  add  7 tag                                                                                                       

epon(GE-5)# vlan  add 33 tag

3.Config OLT manage ip address:

epon# system ipconfig inband 192.168.1.119 255.255.255.0

epon# system ipconfig gateway 192.168.1.1

4.Enable the vlan function:

epon# swmode vlan enable

5.Config the ONU template and apply to all onu,the template config will apply to the ONU.

This template is for the 4port ONU (FD104GH or FD104HC), FD104HW is just 2port(eth1 and eth2) for the ONU and another 2port(lan1 and lan2) is for the wifi port – this ONU needs local web configuratio.

epon# system onu-template-config-user 2

epon(onu-template-2)# config capacity 0 4 0 test

epon(onu-template-2)# config uni 1 ctc vlan-mode tag 0x8100 0 7

epon(onu-template-2)# config uni 2 ctc vlan-mode tag 0x8100 0 7

epon(onu-template-2)# config uni 3 ctc vlan-mode tag 0x8100 0 33

epon(onu-template-2)# config uni 4 ctc vlan-mode tag 0x8100 0 33

epon(onu-template-2)# apply-to-all-onu 2

epon# system save all

 

Done …this is all …easy, right ? Connected ONUs will lease configuration based on this template .

 

 

 

 

The word for the end:

1. your network stands and fall on quality of products you used to build up your network

2. precision and doublechecks saves days of work

3. calculate before connecting

as much as you getting in your hand probably best EOC/optical technology possible for this price tier level with many years of experiences in practical field, s**** may always happend, and thats why we here to help. Do not hesitate to contact us in any need of help, as matter of fact, many of our today customers are willing to help, if you beggining or face problems already known.

We have team possibly eager to help on place of instalation (exept north and south pole areas :) )

 

wodaplug.com networking maniacs team

 

 

The reference projects splitter of computer networks over coaxial cable distribution STA

Adapters Wodaplug® 200C / 500C and N / N

Typical use n1. :

 

1 – Internet Sharing – panel and apartment houses with a shared TV antenna or satellite distribution systems

 

A – housing unit up to 20 connected customers, so just one MASTER unit fed the internet and up to 20 slave units to house

 

Before we begin it is necessary to determine the exact behavior of active components TV / SAT distribution. The problem for the signal to pass through the active elements which are impermeable to the working frequency 2-30MHz. Thus, typically bandpass filters and amplifiers, which operate mostly in a band above 40MHz. Passive components and hubs / multiswitche not a problem.

Now for the actual implementation of customer comments – ISP:

1) The consent of the owner of the house that you can use internal STA / TV distribution

2) typical STA has two satellites and one DVB-T, eg. 12-20 housing units, make sure multiswitch supports reverse channel if it not so, please replace with a new tip

3) when installing recommend the use of freelancers and equipment f

require initial measurement parameters drawers before we hit into the STA.

4) appears problematic active socket for the radio, the ideal would be not to use, with one customer, we found involved in radio and it caused disconnecting HomePlug adapters.

5) The one we configure the modem (enclosed utility Avitar) as MASTER and place it into a hub TV / SAT distribution preferably in a switch cabinet. Internet resource will connect the RJ45 cable to the master. To connect to coaxial cables, we recommend use diplexní filters to split the signal DATA and TV / SAT to avoid interference.

6) then in homes Mounted HomePlug adapters configured as SLAVE. Only communicate with the master unit and can communicate with other SLAVE neighbors. I recommend using the network password could not connect to non-paying users.

Result: now operate about one week, we offer customers the speed 30Mbps shared transmitter on the roof is able to 50Mbps, but we do not want to vytížit entirely to the maximum so that they can connect to other cabins. Now, it looks good.

Recommendation: Before someone decides to run STA on the Internet, they must first of all get the project documentation and STA network, the types of loaded elements attenuation. Top accompanied satelitáře. HomePlug adapters have a good range, high transmission power overcomes even greater attenuation and distance achieved, thus limiting rather HomePlug AV (700 m) than depression.

– This is implemented in practice functional connection example

– In most cases you can secure the network without unnecessary additional costs

– Do not know how to do it ??? matter, please contact us and we will help

 

The topology of the house

socket n.1 – connect rj45 wire to ADSL router or enother device what needs internet connection and connect it to socket with 220v.

socket n.2 – connect rj45 wire to your computer or enother device what needs an internet connection and connect it to socket with 220V.

Done, adapters will connect themselves and allow signal transmission over the wire with 220V.

Congratulations, Now you’ve connected your own home network by the hard way (so it is difficult with WodaPlug)

 

Reference projects split computer networks over electrical cables 230V

 

Adapters Wodaplug2® 85Mb/s, 200Mb/s a Wodaplug3®500Mb/s

 

Typical applications and references from realized projects:

 

1 – internet sharing – three-floor family house with workshop and garage

 

If you live in a multi-floored RD wheres WiFi coverage is all over the floors and it’s still not enought there’s some ideal solution internet distribution and home computer network over the electric wires with 230V, They are in every floor and every room in your house.

 

Example of use in practice :

 

internet supply – ADSL router is located in the ground floor. WiFi signal does not reach up to the third floor and into the workshop, which also needs sometimes access to the Internet.

 

The house is a classic three-phase electric distribution switchgear and circuit breakers. Each floor has two sets of drawers. Floors are not on the same stage. The best quality and the fastest transmission is the same stage after the splitter, but with WodaPlug technology is not the problem of signal transmission between the phases. Transmission is obviously in this case due to the slower attenuation of the signal, but still enough for sharing within a home network for access to fast internet 16Mb / s O2 or distribution of HD IPTV ADSL router to the set top boxes on the upper floors.

One 200 MB/s Wodaplug2 adapter is connected to the RJ45 cable to the ADSL router and plugged into the electrical outlet. On the first floor in the study involved a second adapter Wodaplug2 200 MB/s and Rj45 cable connected to the PC. Here is the transfer after the same stage and the speed is almost at maximum. The third adapter Wodaplug2 200 MB/s + N AP, that has built-in WiFi 802 .11n AP transmitter is designed for notebook and used to carry around the House, workshop and garden and connects to a power outlet in a location where it is needed.Here is the transfer after the same stage and the speed is almost at maximum. The third adapter Wodaplug2 200 MB/s + N AP, that has built-in WiFi 802 .11n AP transmitter is designed for notebook and used to carry around the House, workshop and garden and connects to a power outlet in a location where it is needed.It is of course possible to transfer data between the PC and the NTB, for example, the copy of the film or other documents commonly runs at a speed of 20-30 MB/s if the NTB in the same room with the PC, i.e., on the same stage, runs and 70 MB/s transfer.

 

Note: before the technician replaced the main electric Cez hours for new digital, can share the internet with a neighboring family house. The neighbor had his adapter Wodaplug2 200 MB/s and we shared a single connection to the Internet, the router ADSL could set a limit for its IP transmission speed. Unfortunately, after changing the hours already link does not work due to the fact that the new digital clock frequency filters and contain these releases signal.

Note2: as it is possible for example. share internet in prefabricated or apartment houses between neighbors, according to the references of customers is possible through the connection typically two floors down and two up, hence the 4 floors.

 

2-a paid or free Internet access for the guests of the guest house or hotel

 

Multiple storey guesthouse or hotel complex needs simply and inexpensively offer guests internet access, whether paid or free. Thanks to a few patrům and the area is covered by WiFi signal demanding the installation of HW and i mnoštví WiFi accesspointů would significantly burden the Bill for electricity.

Example deployment in practice:

 

3 storey guesthouse with eight guest room has Internet connection 4 MB/s ADSL and router is located on the ground floor in the central switching station. The Guest House is an old electric splitter with the old Silicon and circuit breakers and fuses the old and often aluminium cables.

To the router are connected two adapters Wodaplug2 85 MB/s using the configuration utilities have each set a different password to be able to separate the work network and network for guests of the Guest House, so that guests could not access and working the front desk and restaurant PC

In the reception and restaurant are connected to other PC adapters Wodaplug2 85 MB/s and using the same password network connected together and with the adapter in a central switching station, which provides access to the internet.

 

In the reception there is also a WiFi router for a free connection to, but the signal reaches only to the first floor and it still not everywhere. Guest House purchased for guests next 4 adapters with Wodaplug2 85 MB/and configuration utility they were preset password of the network, so to have joined with the specified adapter in the switching station. Guests then lend for a fee at the reception in the room is the adapters and plugs into an electrical outlet, connect the RJ45 cable to your laptop or PC and gain access to the shared internet connection. Thanks to the network password is provided that does not connect to the network, for example, a customer with your own adapter of the same communications standard.

 

Signal coverage despite the challenging implementation of the old electro splitter is all over the House, in the outermost points of the bit rate around 5 MB/s, which is sufficient for Internet sharing.

Facebook

Promo Actions

News

  • Nová verze SW pro EOC master

    Je dostupná aktualizovaná verze SW 2.4.0 pro Wodaplug EOC master jednotky. Image pro snadný upgrade přes WEB rozhraní naleznete v sekci download. Novinkou je kompletní management (včetně WiFi a routingu) pro EOC slave s WIFI.

  • Nový model zařízení pro Ethernet přes koax a kompatibilita s 200 a 500C/N

    oblíbený model Wodaplug 200 resp. 500C/N se dočkal vylepšeného nástupce! Dle vašich připomínek jsme připravili nový model vylepšený o IP WEB management, zabezpečení a s pokročilými funkcemi - EoC série! Napište si o vzorky, již dostupné! Zpětná kompatibilita s předchozími modely je díky stejnému čipsetu INT74xx bez problémů možná po přehrání firmware! Přečtěte si návod.

  • Wodaplug3 přichází

    Po dlouholetém úspěchu modelů řady Wodaplug2 přichází nový vylepšený model s novým čipem Qualcom Atheros AR7420 – nejnovější chipset pro větší rychlost, větší dosah a nižší energetickou spotřebu. Podpora IPv6 !! Kompatibilita s předchozími modely standardu HomePlugAV je zachována bez omezení (Wodaplug2 200Mb/s a 500Mb/s).

  • Nový firmware a konfigurační utilita Win7 ready pro adaptér Wodaplug 200C/N s čipem INT6400

    Pro majitele oblíbeného Wodaplug 200C/N s čipem INT6400 jsme připravili konečně novou verzi konfigurační utility AVitar s podporou Windows 7 a nový firmware. Každá verze firmware potřebuje odpovídající verzi konfigurační utility AVitar a odpovídající verzi konfiguračního souboru PIB. Čtěte pozorně pokyny pro upgrade. Ke stažení v sekci DOWNLOAD

Advertising